TPMSProAlbert
02-16-2013, 07:57 PM
45
When new sensors are installed, they must be registered using a FORDTRIGGER TPMS triggering tool.
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard).
2. Turn the ignition switch to OFF then press and release the brake pedal.
3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds.
4. Press and release the brake pedal.
5. Turn the ignition switch back to OFF.
6. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds.
7. The horn should sound letting you know the vehicle has entered into TPMS relearn mode.
8. Place the top of FORDTRIGGER on the sidewall of the driver’s side front tire in the location of the valve stem.
9. Press the button of the FORDTRIGGER tool. The vehicle’s horn will sound letting you know the sensor has been learned.
10. Once the horn sounds, move on to the passenger side front tire and repeat the process. Each tire should only take 30 seconds or less.
11. After the passenger side front tire has been learned, continue on to the passenger side rear tire and finishing with the driver’s side rear tire.
12. You may now turn the ignition to OFF. If the horn does not sound, the sensors were learned successfully. If the horn sounds twice, then the process must be repeated because there was a malfunction.
If your vehicle has push-button ignition:
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard).
2. Make sure the ignition button is OFF then press and release the brake pedal.
3. Hold the ignition button down for 2 seconds, release it, and then tap the button once. The vehicle should be OFF. Hold the ignition button down for another two seconds, release it, and then tap the button once.
4. Hold the ignition button down for two seconds again. The vehicle should be in RUN mode, engine off.
5. Press and release the brake pedal.
6. Tap the ignition button once so the vehicle is OFF.
7. Hold the ignition button down for 2 seconds, release it, and then tap the button once. The vehicle should be OFF. Hold the ignition button down for another two seconds, release it, and then tap the button once.
8. Hold the ignition button down for two seconds again. The vehicle should be in RUN mode, engine off.
9. The horn should sound letting you know the vehicle has entered into TPMS relearn mode.
10. Place the top of FORDTRIGGER on the sidewall of the driver’s side front tire in the location of the valve stem.
11. Press the button of the FORDTRIGGER tool. The vehicle’s horn will sound letting you know the sensor has been learned.
12. Once the horn sounds, move on to the passenger side front tire and repeat the process. Each tire should only take 30 seconds or less.
13. After the passenger side front tire has been learned, continue on to the passenger side rear tire and finishing with the driver’s side rear tire.
14. You may now turn the ignition to OFF. If the horn does not sound, the sensors were learned successfully. If the horn sounds twice, then the process must be repeated because there was a malfunction
When new sensors are installed, they must be registered using a FORDTRIGGER TPMS triggering tool.
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard).
2. Turn the ignition switch to OFF then press and release the brake pedal.
3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds.
4. Press and release the brake pedal.
5. Turn the ignition switch back to OFF.
6. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds.
7. The horn should sound letting you know the vehicle has entered into TPMS relearn mode.
8. Place the top of FORDTRIGGER on the sidewall of the driver’s side front tire in the location of the valve stem.
9. Press the button of the FORDTRIGGER tool. The vehicle’s horn will sound letting you know the sensor has been learned.
10. Once the horn sounds, move on to the passenger side front tire and repeat the process. Each tire should only take 30 seconds or less.
11. After the passenger side front tire has been learned, continue on to the passenger side rear tire and finishing with the driver’s side rear tire.
12. You may now turn the ignition to OFF. If the horn does not sound, the sensors were learned successfully. If the horn sounds twice, then the process must be repeated because there was a malfunction.
If your vehicle has push-button ignition:
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard).
2. Make sure the ignition button is OFF then press and release the brake pedal.
3. Hold the ignition button down for 2 seconds, release it, and then tap the button once. The vehicle should be OFF. Hold the ignition button down for another two seconds, release it, and then tap the button once.
4. Hold the ignition button down for two seconds again. The vehicle should be in RUN mode, engine off.
5. Press and release the brake pedal.
6. Tap the ignition button once so the vehicle is OFF.
7. Hold the ignition button down for 2 seconds, release it, and then tap the button once. The vehicle should be OFF. Hold the ignition button down for another two seconds, release it, and then tap the button once.
8. Hold the ignition button down for two seconds again. The vehicle should be in RUN mode, engine off.
9. The horn should sound letting you know the vehicle has entered into TPMS relearn mode.
10. Place the top of FORDTRIGGER on the sidewall of the driver’s side front tire in the location of the valve stem.
11. Press the button of the FORDTRIGGER tool. The vehicle’s horn will sound letting you know the sensor has been learned.
12. Once the horn sounds, move on to the passenger side front tire and repeat the process. Each tire should only take 30 seconds or less.
13. After the passenger side front tire has been learned, continue on to the passenger side rear tire and finishing with the driver’s side rear tire.
14. You may now turn the ignition to OFF. If the horn does not sound, the sensors were learned successfully. If the horn sounds twice, then the process must be repeated because there was a malfunction